Specifications
|
SIZE in inches(mm) |
|
| Power supply voltage |
DC10 to 15V(Exclusive for 12V vehicle) |
| Current consumption |
+B line MAX 1A only while the closing mode is displayed. (Dark current 0mA) IGN MAX 1A ILM MAX 0.1A |
| Display Range SI |
Speedometer（SP）0～400km/h（0～240MPH） |
| Tachometer(TA)0～9,500rpm | |
Oil temperature（O.TEMP.）50～150 （122～302 ） |
|
| Water temperature（W. TEMP.）20～120（68～248） |
|
| Oil pressure（OIL. P.）0～1,000kPa（0～145PSI） | |
| Fuel pressure（FUEL. P.) 0～600kPa（0～87PSI） | |
| Exhaust temperature（EXT. T.）200～1,100（390～2,010） |
|
| Applicable speed pulse | A) 2, 4, 8, 16(mainly for Japanese vehicles)
B) Free pulse setting: |
| Applicable Number of Cylinders | Without 1, 2, 3, 4, 5, 6, 8 (Set up with D.C.Unit.) If connected to the Defi-Link Control Unit II Version 2.0(DF05002):1, 2, 3, 4, 5, 6, 8* If connected to the Defi-Link Control Unit II(DF05001): 3, 4, 5, 6, 8* If connected to the Defi-Link Control Unit(DF01301): 3, 4, 5, 6, 8* *Set up with each control unit. |
| Gross Weight | 820g, 1.8lb.(including display unit, D.C.Unit, wires, parts, package) |
| NOTE | *This product is for only on vehicles with a 12V electrical system. Never use this product on 24V vehicles. *Engine speed can not be displayed when installed in diesel vehicles. *Engine speed can not be displayed when installed in vehicles without a engine revolution signal. *This product can not be installed in vehicles without a speed signal. *This product can not be installed in altered vehicles. *When sensors are installed additionally, proper sensor attachments are necessary to be purchased. |
Components
The following parts are included with this product. Confirm that all parts are present before installing the product. In addition, these parts are sold separately for part replacement. Contact your retailer for further information.
NOTE: A Japanese operation manual, a wiring manual, and a questionnaire card are included other than the parts listed below. They are effective only in Japan.
| Display unit (wire 8 1/3ft, 2.5m) |
1
|
| D.C.Unit (Exclusive Control Unit) |
1
|
| Speed & Tacho Signal Wire (green/speed, blue/tacho) 6 2/3ft, 2m |
1
|
| Tachometer Signal Wire (Blue) |
1
|
| DIM Sensor (wire 6in, 0.15m) |
1
|
| Power Supply Wire 2 1/2ft, 0.75m |
1
|
| Meter Wire 10in, 0.25m *Use only when connected to the Defi-Link System. |
1
|
| Power Supply Link Wire 10in, 0.25m *Use only when connected to the Defi-Link System. |
1
|
| Control Out Wire (pink) 3 1/3, 1m *Use only when connected to the Defi-Link System. |
1
|
| Operation manual |
1
|
| Terms and Conditions |
1
|
| Double-sided tape |
2
|
| M4 Bolt, Nut, Washer |
1each
|
| Tapping Screw(for Mounting Bracket) |
2
|
| Mounting Bracket |
1
|
| Clamp |
4
|
| Solderless connector |
6
|
Display and DIM sensor
D.C.Unit
Additional parts which need to be purchased
| When this product is used WITHOUT a connection to the Defi-Link System | ||||||||||||||||||
| No part is necessary to be purchased. | ||||||||||||||||||
| When this product is used WITH a connection to the Defi-Link System | ||||||||||||||||||
| <CASE1> Defi-Link Control Unit II (or Defi-Link Control Unit) is already connected. No part is necessary to be purchased. If you want the data which sensors are not connected, the sensor sets(sensor and sensor wire) needs to be purchased. Sensor sets are sold as optional parts. Sensor sets for oil pressure, fuel pressure, oil temperature, water temperature, and exhaust temperature are available. <CASE2> Defi-Link Control Unit II (or Defi-Link Control Unit) is not connected yet.
|
||||||||||||||||||
| OPTIONAL PARTS | ||||||||||||||||||
Sensor thread sizes are all 1/8PT.
|
||||||||||||||||||
| REPLACEMENT PARTS | ||||||||||||||||||
|
